search

Profoto 250 W Guide de l'utilisateur Page 11

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 24
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 10
Profoto D1
11
www.profoto.com
• Thebuilt-inIRreceiversensestheflashreleaseaswellasIRsignalsfrommostIRsync
transmitters.
• TheProfotoAirradiosystemisfullyintegratedintheD1Airunits,allowingradio
synchronization via a Profoto Air Remote or Profoto Air Sync device connected to the
camera, or via the Profoto Air USB device connected to a computer with the Profoto
Studio Air program.
• D1unitswithoutintegratedProfotoAirfunctionalitycanbeequippedwithaProfotoAir
Remote or Profoto Air Sync device acting as receiver, enabling radio synchronization
via another Profoto Air Remote or Profoto Air Sync device connected to the camera.
Ready signaling
Ready signaling is used to indicate when the unit is fully charged. The Ready Button [9a]
is used to select one of four ready signaling alternatives:
• BEEP:Aclear“beep”willsoundtoindicatethatthechargingoftheunitiscompleted.
This setting also enables the control panel sounds, which indicates that a button is
pressed or the Setting Knob is turned.
• DIM:Themodelinglightwillbeturnedoffwhentheunitisbeingcharged,andturned
on again when the charging is completed. This setting also disables the control panel
sounds.
• BEEP-DIM:Themodelinglightwillbeturnedoffwhentheunitisbeingcharged,and
turned on again when the charging is completed. A clear “beep” will also sound to
indicate that the charging is completed. This setting also enables the control panel
sounds.
• OFF:Noreadysignal.Thissettingalsodisablesthecontrolpanelsounds.
Ready indicator/Test function
The Ready Indicator [5] is illuminated when the unit is fully charged and ready to flash.
The Test Button [4] is used to test that all light settings are correct and that the functionality
is as expected. When the Test Button [4] is pressed, the unit will flash and the Ready
Indicator [5] will be turned off while recharging. When the charging of the unit is completed,
the Ready Indicator [5] will be illuminated again.
Flash before ready
The “Flash before ready” function makes it possible to flash before the charging of the unit
is ready and fully completed. When a flash is released before the unit is 100% recharged,
a long “beep” will sound, indicating an under exposed frame. Naturally the flash light may
not correspond fully to the set value.
Vue de la page 10
1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 23 24

Commentaires sur ces manuels

Pas de commentaire
Produits connexes et manuels pour Lampes de travail Profoto 250 W
Lampes de travail Profoto Acute2 manual Guide de l'utilisateur   (24 pages)
Lampes de travail Profoto D1 1000 Air Guide de l'utilisateur    (24 pages)
Lampes de travail Profoto D1 1000 Air Guide de l'utilisateur   (24 pages)
  • EWM Oxygen Joa-telecom The Home and Garden Spas Alpic Air
  • Nextar Projecteurs de données SwissVoice Téléphones APC Commutateurs KVM Bose Lecteurs de CD Husqvarna Perceuses électriques
  • Bosch GBH 11 DE Professional Lenovo A2107A JVC GD-17L1G Samsung PS-58P96FD Electrolux EOA95751BX
  • Electrolux EKK954504X Manuel de l'utilisateur Nec LCD4000 Manuel de l'utilisateur HP 100 Manuel de l'utilisateur Siig Network Card Manuel de l'utilisateur Philips HR2094/00 Manuel de l'utilisateur